Service area · Williamson County

Leiper’s Fork land, hillside chert and bottomland

The ground around Leiper’s Fork runs from cherty material washed down steep hillsides to flat floodplain alluvium, all within a short walk.

TL;DR

Leiper’s Fork is an unincorporated community in Williamson County, about 15 miles from Brentwood. The soils mapped near its center mix Armour on foot slopes and terraces; Dellrose, cherty colluvium on hillsides with a median slope of 16 percent; Captina on gentle uplands; and Huntington on the flood plain. Hillside sites call for walls, steps and erosion control, and bottom ground calls for drainage planning. Being unincorporated, it answers to a Williamson County engineering form for retaining walls four feet or taller.

What should I know before building into a hillside in Leiper’s Fork?

That the hillside may be made of material that has already moved. Dellrose, about 12 percent of the ground sampled near the community’s center, is a very deep, well drained soil formed in cherty colluvium, rock and soil that crept and washed down from higher up, on foot slopes and steep hillsides. It has moderately rapid permeability and a median slope there of 16 percent.

For a wall, steps or a terrace, that means digging to firm, undisturbed material for the base, expecting chert all the way down, and treating water as the main threat, since a wet hillside is the one that slides. Terraces are kept to modest heights, each with stone and pipe behind it, and the cut face above is planted as soon as it is shaped. See Hardscape Construction and Grading & Site Prep.

Does Williamson County require an engineer for a wall in Leiper’s Fork?

For a wall four feet or taller, the county’s own paperwork says so. Leiper’s Fork is unincorporated, which puts it under Williamson County, and a county engineering form from 2015 asks that walls of that height carry a professional engineer’s certification. It also calls for a setback of 5 feet or the wall’s height, whichever is greater.

The form is old enough that its terms are checked with the county before anything is designed around them. On hillside ground, the four-foot line often decides the shape of the project: a single tall wall brings in an engineer, while a stepped series of shorter walls may not. Weighing those options, along with cost and how the terraces will be used, is the work of Project Planning & Consulting.

How should bottomland in Leiper’s Fork be landscaped?

As fertile ground that will sometimes be wet. Huntington, about 8 percent of the ground sampled, is a very deep, well drained soil formed in alluvium on river valley flood plains, and it takes water in readily. It is about as good as planting soil gets around here, for shade trees, big beds and a vegetable garden.

Flood plains do flood, though, so anything built on them should tolerate getting wet: stone and pavers rather than loose materials that float, furniture that can be moved, plants that recover after sitting in water for a day. The flood zone for the property is part of the planning, checked before any structure or grade change is drawn. Landscape Design & Installation works with the ground as it is, and Drainage Solutions deals with water coming off the hills above it.

04Answers

Leiper’s Fork questions

Is the soil in Leiper’s Fork good for gardens?

In the bottoms, very. Huntington soil on the flood plain is very deep and well drained, and Armour on the terraces and foot slopes is deep too. The hillsides are harder: Dellrose is cherty and drains quickly, so beds there need amending, mulch and steady water through their first summer.

How do you keep a Leiper’s Fork hillside from washing out?

By slowing the water and holding the soil. That means terraced walls with drainage behind them, steps that break up a long run, a dry creek bed to carry runoff, and dense planting under mulch on whatever stays sloped. Bare ground on a 16 percent slope loses soil fast, so cover goes on as each section is finished.

Who checks the permit requirements for a Leiper’s Fork project?

Wilhelm Landscapes does, as part of Project Planning & Consulting. Leiper’s Fork is unincorporated, so Williamson County is the authority, and its engineering form asks for an engineer’s certification on retaining walls four feet or taller. The current requirements are confirmed with the county before a design is final.

What is Dellrose soil, and is it in my Leiper’s Fork yard?

Dellrose is a very deep, well drained soil made of cherty colluvium, material that crept and washed down from the slopes above, found on foot slopes and steep hillsides. About 12 percent of the ground sampled near Leiper’s Fork is Dellrose. If your yard is a hillside full of chert, it may well be.

Free estimates

Start with a walk around the yard

Tell Hunter what you have in mind. The consultation and the written estimate are free.

Call Free estimate